View TLP116_353698.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TLP116
Preliminary
TOSHIBA PHOTOCOUPLER GaAlAs LED & PHOTO-IC
TLP116
Digital Isolation for A/D,D/A Conversion. High Speed Line Receiver. Microprocessor System Interfaces. Plasma Display Panel.
The Toshiba TLP116 consists of a GaAl As light emitting diode and a integrated high gain, high speed photo detector. l l l l l l l l l Inverter Logic (totempole output) Package Type : MFSOP6 Guaranteed Performance Over Temperature : -40~100C Power Supply Voltage : 4.5~5.5V Input Thresholds Current : IFHL=5mA(Max.) Propagation delay Time (tpHL/tpLH) : 60ns(Max.) Switching speed : 20MBd(TYP.) (NRZ) Common mode transient immunity : 10kV/us Isolation Voltage : 3750Vrms JEDEC TOSHIBA Weight: 0.09 g Unit in mm
11-4C2
Truth Table
Input H L LED ON OFF Tr1 OFF ON Tr2 ON OFF Output L H
Pin Configuration (Top View) 1
VCC
6 5
1:ANODE 3:CATHODE 4:GND 5:VO 6:VCC
ICC 6 VCC
3 Schematic
IF 1*{ VF 3*|
GND
Tr1 IO VO Tr2 5
SHIELD
4
GND
0.1uF bypass capacitor must be connected between pin 6 and 4
1
2003-10-21
TLP116
Recommended Operating Conditions
CHARACTERISTIC Input Current , ON Input Voltage , OFF Supply Voltage Operating Temperature SYMBOL IF(ON) VF(OFF) VCC Topr MIN. 8 0 4.5 -40 TYP. MAX. 18 0.8 5.5 100 UNIT mA V V C
-- --
5.0 --
The correlation between input current and switching speed and drive circuit (reference information).
Input Current (IF) 12mA 8mA 8mA 1 (Page 4) 1 (Page 4) 2 (Page 4,With Speed up capacitor) 21 - 23 MBd 18 - 20 MBd 23 - 27 MBd TEST CIRCUIT Typical Switching Speed
Maximum Ratings (Ta=25C*j
CHARACTERISTIC Forward Current LED Forward Current Derating (Ta=85C) (Note1) SYMBOL IF ? IF/? Ta IFPT VR IO VO VCC PO Topr Tstg Tsol 5 10 6 6 40 -40~100 -55~125 260 RATING 20 -0.5 UNIT mA mA/C A V mA V V mW C C C
Peak Transient Forward Current Reverse Voltage
DETECTOR
Output Current Output Voltage Supply Voltage Output power dissipation
Operating Temperature Range Storage Temperature Range Lead Solder Temperature(10s) Isolation Voltage
(AC,1min.,R.H.=60%,Ta=25(C)
(Note2)
BVs
3750
Vrms
Note1 : Pulse width PW=10us,500pps. Note2 : Device Considered a two terminal device : pins 1 and 3 shorted together and pins 4,5 and 6 shorted together.
2
2003-10-21
TLP116
Electrical Characteristics (Unless otherwise specified, Ta=-40 to 100C,VCC=4.5~5.5V)
CHARACTERISTIC Input Forward Voltage Temperature Coefficient of Forward Voltage Input Reverse Current Input Capacitance Logic Low Output Voltage Logic High Output Voltage Logic Low Supply Current Logic High Supply Current Input Current Logic Low Output Input Voltage Logic High Output SYMBOL VF ?VF/?Ta IR CT VOL VOH ICCL ICCH IFHL CONDITION IF=10mA ,Ta=25C IF=10mA VR=5V,Ta=25C V=0,f=1MHz,Ta=25C IOL=1.6mA, IF=12mA,VCC=5V IOH=-0.02mA , VF=1.05V,VCC=5V IF=12mA VF=0V IO=1.6mA,VO<0.4V (Note 3) MIN. -- TYP. 1.3 MAX. 1.5 UNIT V mV/C E A pF V V mA mA mA
-- -- -- --
4.0
-- -- -- -- -- -- -- --
10
--
0.4
--
5.0 5.0 5
-- -- --
0.8
VFLH
IO=-0.02mA,VO>4.0V
--
V
*All typical values are at Ta=25C,VCC=5V,IF=(ON)=12mA unless otherwise specified Note3 : The Photodetector needs VCC of 4.5V or more for the stability operation. In the VCC range less than 4.5V,ICCH may increase in some part of VCC range. It is recommended to check operation of power supply stability in timing at power supply ON, and OFF before product is used.
Isolation Characteristics (Ta = 25C)
Characteristic Capacitance input to output Isolation resistance Symbol CS RS Test Condition V = 0,f = 1MHz R.H. = 60%,VS = 500V (Note 2) AC,1 minute Isolation voltage BVS AC,1 second,in oil DC,1 minute,in oil (Note 2) Min. ? 1x10
12
Typ. 0.8 10 ? 10000 10000
14
Max. ? ? ? ?
Unit pF O Vrms Vdc
3750 ? ?
?
3
2003-10-21
TLP116
Switching Characteristics (Unless otherwise specified, Ta=-40 to 100C,VCC=4.5~5.5V*j
CHARACTERISTIC propagation Delay Time to Logic High output propagation Delay Time to Logic Low output propagation Delay Time to Logic High output propagation Delay Time to Logic Low output Switching Time Dispersion between ON and OFF Output Fall Time(90-10%) Output Rise Time(10-90%) Common Mode transient Immunity at High Level Output Common Mode transient Immunity at Low Level Output *All typical values are at Ta=25C Note 4 : CL is approximately 15pF which includes probe and Jig/stray wiring capacitance. CML CMH SYMBOL TEST CIRCUIT CONDITION MIN. TYP. MAX. UNIT
tpHL
IF=0*12mA
RIN=100 CL=15pF (Note 4) RIN=470 CIN=27pF CL=15pF (Note 4)
-- -- -- -- -- -- --
-- -- -- -- --
60
ns
1
tpLH IF=12*0mA VIN=0*5V (IF=0*8mA) 2 tpLH |tpHLtpLH| " ' " 1 VIN=5*0V (IF=8*0mA)
60
ns
tpHL
60
ns
60
ns
IF=12mA , RIN=100, CL=15pF (Note 4) IF=0*12mA IF=12*0mA RIN=100 CL=15pF (Note 4)
30
ns ns ns
-- -- -- --
VCM=1000Vp-p,IF=0mA, Vo(Min)=4V,Ta=25C
10000
V/us
VCM=1000Vp-p,IF=12mA, Vo(Max)=0.4V,Ta=25C
-10000
--
--
V/us
TEST CIRCUIT 1 : tpHL , tpLH
(f=5MHz , duty=50%)
IF=12mA(P.G)
VCC 0.1uF
INPUT MONITORING NODE Vo MONITORING NODE
50%
IF
VCC
VO
GND SHIELD CL=15pF RIN=100
CL=15pF
VOH
1.5V
VOL
tpHL
tpLH
TEST CIRCUIT 2 : tpHL , tpLH
VIN=5V(P.G)
INPUT MONITORING NODE (f=5MHz , duty=50%)
VCC CL=15pF 0.1uF
Vo MONITORING NODE
VIN
VCC
50%
VO
GND SHIELD CIN=27pF RIN=470
CL=15pF
VOH
1.5V
VOL
tpHL
The PROBE and JIG capacitances are included in CL. (P.G) : Pulse Generatior
tpLH
4
2003-10-21
TLP116
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice.
030619EBC
* The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The products described in this document are subject to the foreign exchange and foreign trade laws. * TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. * GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or dissolve chemically.
5
2003-10-21

▲Up To Search▲

Price & Availability of TLP116

	To Download TLP116 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .